Silverfish Longboarding - The Longboard Skateboarding Community - View Single Post

Tobes · 10-02-2006, 07:54 AM

Ok, there are just too many posts about repeated questions so I hope to bring this thread to the board and answer any question someone new to sliding might have.

Where to start

What board, wheels, trucks, bearings, should I get for sliding?
Ok before you read what I say about this, there is a ton of more in depth information found here.

Board
Basically its personal preference, ANY board can be used for sliding but some people prefer boards like the Earthwing Slider for trick sliding while others prefer the Gravity Brad Edwards 40" because of its size. If you are of larger size, perhaps you should look into a longer board for a larger stance and more room to get down low, if your of smaller size it would make sense that a small board would be easier to control for you. Nothing is set in stone though, it really is all personal preference. The first step before you ask any questions should be to look at boards and decide which ones you may like. There is a vendor's and manufactures list that can be found here.
Vendors & Manufacturers Contact List

Check the list, find a store, look at some boards and then search the forums for opinions and more details on those particular boards. If you can't find anything THEN you should post about it.

Wheels
What wheel do I want?
Any wheel can slide, it is just easier on to unlock with a harder duro wheel. While different wheels are easier to unlock and some lock back in easier, it is possible to slide on 73a and with some wheels it is actually pretty easy. Do a search, chances are the wheel you have a question about has been talked about. Yet again, go check out an online store and find ones that interest you and search the forums for different wheel suggestions, like I said chances are the wheel has been discussed. If not make a post about it. And just so you know, the wheel that is best for sliding is the one you like the most, its all personal preference.

Trucks
Not discussed as much as decks and wheels, trucks are obviously an important part of a complete board. But yet again it boils down to personal preference. Some people prefer loose trucks and some prefer tight or in between. Take the advice above and find some that interested you and do a search.

Bearings
Spacers are a great purchase for the extra 5 bucks they will greatly increase the life of your bearings and they will also decrease the chance for flatspotting and promote more even wear on your wheels.
Thanks to eazylax and Crappysurfer2 for this contribution.
Other then spacers finding the correct bearings is as simple as using the advice given above.

Gear

Ok so its not all about the board when it comes to sliding, gloves and padding is important too. But where can you get gloves and is padding really necessary?

Gloves
One of the most used tools in most sliding, so you want to get some good gloves? Well you can buy them from a store, using the advice above I'm sure you can find a discussion or two on a particular manufactures gloves. OR you can make your own, there are a billion and one discussions on this so I will only give you a link to one or two ways. If you want to know more do a search on it!
http://www.chrischaput.com/gloves/ - Found in the sliding links thread.

Pads & Helmet
Seriously one of the best investments I made for learning how to trick slide. You will get torn up, ripped up, rubbed up, rashed up, bruised up, beaten up and perhaps blown up so get some pads and you will be amazed at how much they help. Search the forum for more info, most pads have been discussed and you will be able to find plenty of info. And don't forget, PROTECT YOUR NOGGIN! You only get one brain, don't paint the pavement red with it.

What slides should I learn?

Start off with the simple ones, coleman(this should be your first slide as it is a great one to use to make emergancy stops or to slow down), heelslides, toeslides things of that nature. Do what you feel comfortable doing. The more speed you get the easier it is to slide, but yet again do what you feel comfortable doing. Examples of these slides can be found all over the board but a great place to start looking is here. In perticular I suggest looking at the Faltown Slide School, a great place to learn the basic and more advance slides.

I highly suggest looking at the faltown skate skool link in the thread mentioned above, and basically any other link in that thread because they all provide good information.

If your having trouble with a particular slide or perhaps getting that last 90 degrees on your surrender 360 then do a search there is a lot of advice that is already out there. Usually there is also a thread already up there talking about technique and similar things.

\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/
================================================== =================================
/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\

I tried to cover most of the basics, looking for links to add to certain sections like gloves, good online resources for equipment, and anything that reduce the amount of searching a newbie would have to do. Tips and suggestions on how to improve this would be much appreciated, I just am trying to get everything organized into one post.

Thanks!

10-02-2006, 07:54 AM	#1 (permalink)
Tobes Addicted Cruiser Join Date: Aug 2006 Age: 21 Posts: 476	New to sliding? Ok, there are just too many posts about repeated questions so I hope to bring this thread to the board and answer any question someone new to sliding might have. Where to start What board, wheels, trucks, bearings, should I get for sliding? Ok before you read what I say about this, there is a ton of more in depth information found *here. Board* Basically its personal preference, ANY board can be used for sliding but some people prefer boards like the Earthwing Slider for trick sliding while others prefer the Gravity Brad Edwards 40" because of its size. If you are of larger size, perhaps you should look into a longer board for a larger stance and more room to get down low, if your of smaller size it would make sense that a small board would be easier to control for you. Nothing is set in stone though, it really is all personal preference. The first step before you ask any questions should be to look at boards and decide which ones you may like. There is a vendor's and manufactures list that can be found here. Vendors & Manufacturers Contact List Check the list, find a store, look at some boards and then search the forums for opinions and more details on those particular boards. If you can't find anything THEN you should post about it. Wheels What wheel do I want? Any wheel can slide, it is just easier on to unlock with a harder duro wheel. While different wheels are easier to unlock and some lock back in easier, it is possible to slide on 73a and with some wheels it is actually pretty easy. Do a search, chances are the wheel you have a question about has been talked about. Yet again, go check out an online store and find ones that interest you and search the forums for different wheel suggestions, like I said chances are the wheel has been discussed. If not make a post about it. And just so you know, the wheel that is best for sliding is the one you like the most, its all personal preference. Trucks Not discussed as much as decks and wheels, trucks are obviously an important part of a complete board. But yet again it boils down to personal preference. Some people prefer loose trucks and some prefer tight or in between. Take the advice above and find some that interested you and do a search. Bearings Spacers are a great purchase for the extra 5 bucks they will greatly increase the life of your bearings and they will also decrease the chance for flatspotting and promote more even wear on your wheels. Thanks to eazylax and Crappysurfer2 for this contribution. Other then spacers finding the correct bearings is as simple as using the advice given above. Gear Ok so its not all about the board when it comes to sliding, gloves and padding is important too. But where can you get gloves and is padding really necessary? Gloves One of the most used tools in most sliding, so you want to get some good gloves? Well you can buy them from a store, using the advice above I'm sure you can find a discussion or two on a particular manufactures gloves. OR you can make your own, there are a billion and one discussions on this so I will only give you a link to one or two ways. If you want to know more do a search on it! http://www.chrischaput.com/gloves/ - Found in the sliding links thread. Pads & Helmet Seriously one of the best investments I made for learning how to trick slide. You will get torn up, ripped up, rubbed up, rashed up, bruised up, beaten up and perhaps blown up so get some pads and you will be amazed at how much they help. Search the forum for more info, most pads have been discussed and you will be able to find plenty of info. And don't forget, PROTECT YOUR NOGGIN! You only get one brain, don't paint the pavement red with it. What slides should I learn? Start off with the simple ones, coleman(this should be your first slide as it is a great one to use to make emergancy stops or to slow down), heelslides, toeslides things of that nature. Do what you feel comfortable doing. The more speed you get the easier it is to slide, but yet again do what you feel comfortable doing. Examples of these slides can be found all over the board but a great place to start looking is *here. In perticular I suggest looking at the Faltown Slide School, a great place to learn the basic and more advance slides. I highly suggest looking at the faltown skate skool link in the thread mentioned above, and basically any other link in that thread because they all provide good information. If your having trouble with a particular slide or perhaps getting that last 90 degrees on your surrender 360 then do a search there is a lot of advice that is already out there. Usually there is also a thread already up there talking about technique and similar things. \/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/ ================================================== ================================= /\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\/\ I tried to cover most of the basics, looking for links to add to certain sections like gloves, good online resources for equipment, and anything that reduce the amount of searching a newbie would have to do. Tips and suggestions on how to improve this would be much appreciated, I just am trying to get everything organized into one post. Thanks! __________________ Quiver:* Sector Nine Zen, Revenge Type II trucks, S9 Nineball 73a wheels. Earthwing Slider 35.5", Gullwing Mission 1 Trucks, Sergio Slider wheels. Kebbek Jon Caften, Force C7 trucks, Abec 11 83mm 75a Flys, Baillistech Missle Bearings. Last edited by Tobes; 10-15-2006 at 08:25 PM.

Sponsored Links