Indy DH plate

vince-t · 07-09-2009, 12:07 AM

Quote:

Originally Posted by Tboy

Q #1: Also, since it's basically an "already dewedged" indy truck, then it's gonna work well with latenite's reverse KP front and dewedged indy rear setup right?

yea itll work well if not better than the reverse kp front and indy rear. it would even be lower since when you dewedge a standard indy truck it raises the height a little....logically at least, depending on what the final height of streets design will be

Sandwich · 07-09-2009, 08:48 AM

Here you go
These first pictures are the 0 degree kingpin (or 90 degree however you want to look at it)

I will make a 5, 10, and 15 degree king pin base plate also. Right now the stock kind pin is at about 17 or 18 degrees.

this is the 5 degree kingpin plate

this is the 10 degree plate

and last of all the 15 degree kingpin plate

Now just give me a few hours and I can have a working prototype of the 0 degree kingpin plates

lfatboy · 07-09-2009, 08:52 AM

Yayyyy

thokk2 · 07-09-2009, 08:52 AM

Just found this thread... wow... This is amazing. Any idea on price?

gavmck · 07-09-2009, 08:58 AM

Sandwich is the MAN! I don't even want these, not my thing, but I love the way he makes stuff so fast based on rider input.

SIIICK

wooden · 07-09-2009, 09:30 AM

i've been wanting a set of indies forever, this may push me to get them now that there's more than just the standard 17/18* plates.

Sandwich · 07-09-2009, 11:54 AM

They will be about $95.00 for a set of these plates.
I've only made the 0 degree kingpin so far, I'm not sure when I'll be able to make the others. I will be going on a 7 day road trip on sunday.

I will send a few out to get tested before I start selling them, but I think you can count on two to three weeks from now before they are available.

I know the kingpin that I used is 1/4 inch too long, but thats all I had.

Enjoy

thokk2 · 07-09-2009, 11:56 AM

Beautiful! I wish I had the money... Do you need a tester?

schmoose · 07-09-2009, 12:04 PM

Quote:

You have given out too much Reputation in the last 24 hours, try again later.

DAM DAM DAM DAM DAM!!!!!!!!
that looks really nice man, I would pay to test some!!!

bpz · 07-09-2009, 12:07 PM

Wow those look seriously RAD.

Rouleau · 07-09-2009, 01:02 PM

silverfish at it's finest

AJ · 07-09-2009, 01:54 PM

That looks like fun.
but I'll stick to angled risers, the ride height is nice anyways...

Must be hella light though, I wonder what Merchoochoo will say on these?

Blackmore · 07-09-2009, 01:57 PM

Those look sick, iwill definitely pick up a set once i get some money

jman1365 · 07-09-2009, 02:14 PM

Quote:

Originally Posted by thokk2

Beautiful! I wish I had the money... Do you need a tester?

I volunteer for testing if one is needed as well.

Archy · 07-09-2009, 02:47 PM

Quote:

Originally Posted by Rouleau

silverfish at it's finest

QFT. Too cool.

bakersfield90 · 07-09-2009, 03:03 PM

Quote:

Originally Posted by Archy

QFT. Too cool.

QFTFT. Too cool.

bpz · 07-09-2009, 03:08 PM

I think Mercado should be sent a set just cause he's so badass.

CasterTown · 07-09-2009, 03:22 PM

Quote:

Originally Posted by Sandwich

They will be about $95.00 for a set of these plates.
I've only made the 0 degree kingpin so far, I'm not sure when I'll be able to make the others. I will be going on a 7 day road trip on sunday.

I will send a few out to get tested before I start selling them, but I think you can count on two to three weeks from now before they are available.

I know the kingpin that I used is 1/4 inch too long, but thats all I had.

Enjoy

Amazing. Anyone wanna buy my kahas so I can get a plate?