your dh setup

[Miniman]

Pardon?

[XYZ]

You'll be fine w/ the 35 bp's & 1inch axles. SOFTER bushings may provide what you're looking for in regards to a closer feel to the randals. And even closer, plunk down $60 for a 45 baseplate. Personally, I don't think it's necessary -that's the beauty of the Talons.

Because of my current bushing setup, my ride is slightly loose / turny but stable all the while going fast. Hence, not (loosy goosy).

[Miniman]

Thanks alot man! Are you able to order 45 degrees if you give them 60 bucks more?

[Captain Matt]

i just realised i never posted my boards...

[bean-a-reano]

I know you have a voodoo on the left, what is on the right? The front doesn't have the cutouts.

[gorillabiscuits]

It's Eli Smouse's old DH board. The WB and width are almost the same. The concave is a little deeper and the board a bit heavier. I think he shaped it himself. It's a sweet ride though, just like the voodoo.

[TheFuzz]

my flexy VA speedboard

[kennyr996]

Rayne Demonseed
Randal Downhill baseplates
Randal 180 flipped hangers
Biltin Abec 7 bearings
90mm Flywheels 78a

[bpz]

Rayne Demonseed
Randal Downhill baseplates
Randal 180 flipped hangers

Does that turn.... like, at all?

[small hippo1]

Rayne Demonseed
Randal Downhill baseplates
Randal 180 flipped hangers

Does that turn.... like, at all?

dh baseplates and flipped hangers....you cant turn at all.

[Longbord1]

maybe he uses khiro whites?

[bpz]

maybe he uses khiro whites?

Sweet... so he can get the hangers to hit the board while he's not turning? Or can he clip the ground with the rails of the deck while he's not turning? Sounds like fun not turning, either way.

[HerBDerb]

Stop raggin on the guys setup.
I'm sure he has it tuned to what he likes.

[Basch]

DH plates and flipped hangers do turn. Jus go fast enough. It redicoulisly stable but still carves at speed.

[Rustyfriend]

when dh's are on a board that does not have the severe drop of a DH race or the severe dewedge in the rear, they aren't half bad

[Miniman]

The guy that has the best gear wins? Right guys?

Some of the people here are kind of inoing!

[Tony]

I best I better post my new racing setup.
Rayne avenger
Dh baseplates
SgS 10mm hangers
Sin system bearings
goddess of speed wheels.

[Triomphe]

This guy told me that he's JimZ with 35 turned more than his r2 just because of the Sphearical bearing in hanger and pivot!

If someone could help me with this, i would be superhappy!

//Olle van Keppel

I have a set of Jimz on 35* plates and RIIs (who doesn't?) and I've actually ridden both of them today (both set up pretty loose) and I can tell you for a fact that the Jimz will NOT turn more than the RIIs... (Jimz bushings with the 35* plates and Jimz hangers, Khiro blue on RIIs) Also the Jimz only have a spherical bearing in the hanger and the pivot has a zero slop pivot pin and UHMW cylindrical sleeve.

[Miniman]

Thanks lad, havent tried them!

[GravityMan92]

my brand new set-up-

Subsonic "reflex" 42(Like the evo, except kicks 10x more ass)
Randal 180's flipped(Also expiramenting with seismics)
PINK gumballs
Biltin abec 7's

dreams do come true...