your dh setup

[boardin'mormon]

Yeah bolt the back holes to another plate which has oldschool holes. Make sure it's pretty centered or you'll screw everything up. Use the plate as your guide.

great idea! i did the same thing but used a 6 hole plate and bolted all 4 then drilled through 6 bolt one worked really well but be carefull

[streetheap]

great idea! i did the same thing but used a 6 hole plate and bolted all 4 then drilled through 6 bolt one worked really well but be carefull

Totally thought I put that part in my reply too. I'm getting forgetful in my old age.

[boardin'mormon]

holy mormons, you just tripled my rep!

anyways heres my setup

landy evo (old school with the dinomite graphic)
made to work bandals - bear hangers with 50* randal r2 plates 7* dewedge in front
venom barrols up fornt with a custom back bushing set up
worn down lime bigzigs with reds

[FlamingLongboarder]

made to work bandals - bear hangers with 50* randal r2 plates 7* dewedge in front

Pics?

10madetoworks

[DRC]

great idea! i did the same thing but used a 6 hole plate and bolted all 4 then drilled through 6 bolt one worked really well but be carefull

I attached my indy plates to a spare randal plate I had sitting around. Looking at the now modified Indy plate the new holes don't look inline with the original ones, they both look a little too left and right respectively.

Everything fits together perfectly though, so no complaints. I used a drill press to drill it out, took literally about a minute a plate

[snozzboarder55]

I attached my indy plates to a spare randal plate I had sitting around. Looking at the now modified Indy plate the new holes don't look inline with the original ones, they both look a little too left and right respectively.

Everything fits together perfectly though, so no complaints. I used a drill press to drill it out, took literally about a minute a plate

Randal use to have some bad QC issues before Breamo took over. if you have an old batch it could be misaligned thus giving you a "bad" template to work off of. but it works so its not anything to be concerned about.

[DRC]

Randal use to have some bad QC issues before Breamo took over. if you have an old batch it could be misaligned thus giving you a "bad" template to work off of. but it works so its not anything to be concerned about.

Aah, I think it might be an old plate. I really like the old gen randal hangers better though. Nicer bushing seat IMO, fits 35* plate, and reflex bushings much better.

The holes were snugger on the bolts despite being the same size as the others so I drilled them a liiittlle bigger than normal and all was good. No more need to have the plate perfectly flat while putting it on the board.

[boardin'mormon]

Pics?

10madetoworks

sure as soon as my camera gets back from the repair shop
basicly what i did was i got a pivit cup that fit the bears pivit point then used some heat molded plastic (my friend had some left over from a project) then used that to make a filler for in between the pivit cup and the pivit cup hole of the randals... there really isnt any performance gain, its more of a mental thing for me, i like having a bit of a beefier hanger and i also like how the randal plates are a bit thicker than the bears ones... however i really like useing randal hangers on bear plates on my vanguard it gives a nice carvy feel plus the fact the metal on the botttom of a bear plate is slighty thinner than a randals, allowing me to run a shockpad with littler height gain, as for that my pivit cup for my bears was really worn so the randals just worked

oh, and glad the indys worked out far ya!
hope that helped

[SoldierOfSpeed]

cut it up made it much stiffer

[a_speck_of_dust]

ftl!

[drewdub]

cut it up made it much stiffer

I'm about to do that to my 42''. So is it a 40'' now?

[arizona_123]

cut it up made it much stiffer

riley, what dont you cut?

[SoldierOfSpeed]

riley, what dont you cut?

not gunna lie, i have no idea what that means

[Blackmore]

i think he is talking about your p-niz

[arizona_123]

not gunna lie, i have no idea what that means

im talkign about, rumor has it, ALL the boards you have, you cut lmao

[bemmons1222]

chopping boards is awesome! i've chopped most of my boards and i always like them way better after. probably won't be chopping my 38" race though, it's basically perfect as is

[snozzboarder55]

chopping boards is awesome! i've chopped most of my boards and i always like them way better after. probably won't be chopping my 38" race though, it's basically perfect as is

abso-****ing-lutely. i chopped a few decks and they have all turned out better. currently loving my chopped hellcat, and i just set up my chopped jp36 with bears we'll see how it goes.

chopping boards is not only fun its a good way to "customize" a ride and fit for you personally... cheaper than buying a new deck too

[vince-t]

not gunna lie, i have no idea what that means

haha i think he's referring to the amount of your boards that you hack to your liking

[Justin K]

im talkign about, rumor has it, ALL the boards you have, you cut lmao

What are you even talking about? he has cut 3 boards.

[wardlarson]

cheaper than building one lol