Vintage Old School page 50's and up

[pennypusher]

Can anyone tell me the duro of the pink Kryp C-62s? Thanks.
I went through the thread, here. Awesome read.

Old School Skates - Detail

[GriffinSk8]

Not a lot of turn on these trucks.

[LaneMeyer]

Damn those are like the original reverse kingpin trucks!

except they mount backwards.

[GriffinSk8]

Damn those are like the original reverse kingpin trucks!

except they mount backwards.

You should see the square rubber bushing in the middle of the truck. It's around a 1/2" in size.

[krownraider43]

oh cool! its been a while since i got on the forum and i had no idea a 'vintage' section had been added!! well then, lemme re-post the pix i had up at one time of my old skool jupiter board:







this is the original setup, and i rode it just this way with only changing out the bearings to bones *reds* and bushings to green doh dohs for a while before changing out the trucks for tracker darts, and no skoolz wheels.

rite now i'm going thru a bit of a vintage phase cos i've been riding this board alot lately and just yesterday i changed the wheels out to my 70's flashbacks and i noticed a HUGE difference in the ride...extremely smoooooth!

cool section!! thanx for adding it!!!

[Griff223]

My friend found a board. It is blue aluminum with BANZAI engraved on top. the wheels are no name, but they are sub 60mm and have lips and loose ball bearings. they are road rider ish colored. this board is tiny. the trucks say banzai 11cm on them, which must be the axle length because they are half the width of my rtx 106mm. kingpins have flat screwdriver heads, and the bushings are red double barrels, which still look good. the trucks do not use a standard truck mounting hole pattern like new or old school. it is smaller.

any idea how old this is, if it has any value, or any other info?

[BryceGS]

My friend found a board. It is blue aluminum with BANZAI engraved on top. the wheels are no name, but they are sub 60mm and have lips and loose ball bearings. they are road rider ish colored. this board is tiny. the trucks say banzai 11cm on them, which must be the axle length because they are half the width of my rtx 106mm. kingpins have flat screwdriver heads, and the bushings are red double barrels, which still look good. the trucks do not use a standard truck mounting hole pattern like new or old school. it is smaller.

any idea how old this is, if it has any value, or any other info?

Have double kick-tails? Remember someone having a Banzai w/ road riders on it. Pretty sure the road rider wheels were aftermarket, though. '76-'77?

[chees-]

grentec coyote 2 with serious problems need help.


washer that held the bearings on is rusted on i think and is almost impossible to remove without ruining the hangers would like to salvage hangers and wheels if possible if not then the wheels their 54mm by 54m so super sweet looking and ride ok

[Griff223]

Have double kick-tails? Remember someone having a Banzai w/ road riders on it. Pretty sure the road rider wheels were aftermarket, though. '76-'77?

yes. it has a tiny nose kick and and small back kick.

[BryceGS]

My friend found a board. It is blue aluminum with BANZAI engraved on top. the wheels are no name, but they are sub 60mm and have lips and loose ball bearings. they are road rider ish colored. this board is tiny. the trucks say banzai 11cm on them, which must be the axle length because they are half the width of my rtx 106mm. kingpins have flat screwdriver heads, and the bushings are red double barrels, which still look good. the trucks do not use a standard truck mounting hole pattern like new or old school. it is smaller.

any idea how old this is, if it has any value, or any other info?

Vol 5: Skateboard Industry News Issue ONE 1977 Ads

Google banzai skateboards, plenty of info.

Was always leary of those sharp nosed boards, looks like they would hurt if hit by one!

[Griff223]

Vol 5: Skateboard Industry News Issue ONE 1977 Ads

Google banzai skateboards, plenty of info.

Was always leary of those sharp nosed boards, looks like they would hurt if hit by one!

thanks. is it worth restoring? would anyone want to buy it as a collector's item?

[Bevilacqua]

I suppose it looks a lot like this:


very collectible
not so much value

[Ogre]

I suppose it looks a lot like this:


very collectible
not so much value

My first sealed bearing set up..but with RR #2's and x calibers

[DHBM]

so I found this in a garage here in SD, anyone know anything about it?

[Terrorsathan]

I'm trying to get a value and/or sell this Fibreflex with Gullwing Pheonix

anyone know anything:

[Ogre]

I'm trying to get a value and/or sell this Fibreflex with Gullwing Pheonix

anyone know anything:

Ballpark 300 .00 if the market's right

[Terrorsathan]

Hell, I'd take 100 for it.

[DHBM]

i've got a retired board and was looking at the wheels.

they're in O.K. condition. they've been ridden prolly have 40 miles on em easy.

but they look ok and still ride really well.

I have old school blue krypto's, at least i think they're krypto's this is the only pic i have of them. i'll try and get more.

[Ogre]

look like Krypto conicals

[DHBM]

look like Krypto conicals

any idea how much i could auctiion them off for?